top of page

Electrical Engineer and PE Stamp for Permit Plans in San Diego County, California

When a San Diego County plan check correction calls for an electrical engineer’s signature, send us the set.

​

Jerry Poon, PE, of Red Dog Engineering is a California-licensed electrical engineer for permit plans in San Diego County. We review contractor-prepared electrical drawings, make changes where needed, and sign and stamp them as the engineer in responsible charge. Our San Diego work is commercial, industrial and lab space. The City of San Diego requires electrical plans and calculations for “all buildings and structures other than one-and two-family dwellings.” Delivery is remote, with an electronic seal. Expedited review is available. Scope, turnaround, and fee follow our review of what you send.

 

Send the set, the correction letter or GC exhibit, the jurisdiction, the deadline, who prepared the drawings, and whether your firm is installing.

​

Email jerry@reddog.engineering or call (626) 428-9005.

​

Jerry Poon, PE, California #20878 — verify at the Board’s license lookup. Last reviewed November 10, 2026.

​

The City of San Diego requires “a licensed electrical engineer” on electrical plans unless the contractor both designs and installs the work. Each jurisdiction’s rule is quoted below.

Have a San Diego County Correction That Calls for an Electrical Engineer?

Send the PDF set, the correction letter, and the jurisdiction. You get a written scope, turnaround, and fee.

​

Or email directly: jerry@reddog.engineering

Who Can Sign Electrical Plans in San Diego County, by Jurisdiction

Each jurisdiction publishes its own rule. We have permitted electrical work in most cities in San Diego County and with County PDS. For a city not listed, send the jurisdiction with the set.

​

Who Can Sign Electrical Plans in the City of San Diego?

“The electrical plans and calculations shall be signed by a licensed electrical engineer.” A contractor may sign “only if he/she is responsible for both the design and installation of the system.” Plans are required “for all buildings and structures other than one-and two-family dwellings except when the installation qualifies for a no-plan permit.” Sets are uploaded as PDFs: “Your PDF documents MUST meet our upload requirements.”

​

Source: Plan (required) Electrical Permit, no date shown

​

Who Signs Electrical Plans in Unincorporated San Diego County?

The County’s “Who May Prepare Plans” form does not address electrical plans, so state law decides who signs them. Its commercial tenant improvement checklist says “You must retain the services of a California-licensed engineer or architect to help you prepare your plans and respond to the corrections on this list.”

​

Source: PDS 118, Rev. 09/24/2012; PDS 692, Rev. 01/02/2021

​

Who Can Sign Electrical Plans in Chula Vista?

“The signature of a licensed electrical or mechanical engineer or a licensed contractor operating within the limits of Section 6737.3 of the California Business and Professions Code can satisfy this requirement.” New commercial and industrial submittals include “Electrical Plans” and a “Single line diagram for electrical services over 200 amps”.

​

Source: Form 4610, Rev. 12/28/07; Form 4561, no date shown

electrical-engineering-16.webp

What Does Escondido Require on Commercial Electrical Plans?

“All plans must be signed upon submittal. Per State law, all licensed individuals must also stamp all submittal documents.” “All commercial/industrial projects regardless of size … require complete electrical plans”. “As of August 1, 2022 - The Building Division will only accept plans in an electronic format.”

​

Source: Guideline 7, April 2025

​

Does Oceanside Require Stamped Plans for Commercial Projects?

“In general, a licensed design professional is required for all commercial projects.” “Paper plans will no longer be accepted.”

​

Source: Plan Check page

​

Who Signs Electrical Plans in Poway?

“If the plans have been drawn by an engineer, designer, or architect, each page shall be signed.” “An electrical plan is required for commercial projects.” “Each page shall be numbered and the entire plan set shall be submitted in a single .PDF file.”

​

Source: Building Permit Plans & Requirements, no date shown

​

Carlsbad: What the Electrical Plan Must Show

The tenant improvement bulletin does not say who signs. It says “The electrical plan should include a single line diagram of any proposed new and all existing panels,” and “When the electrical service overcurrent device is made larger, a load calculation for the service is required.”

​

Source: B-6 Tenant Improvements, Rev. 08/26

​

Vista: What a Tenant Improvement Submittal Includes

The handouts do not say who signs. A tenant improvement submittal includes “Two (2) sets of electrical load calcs/single line diagram,” and the single line must “Show serving voltage, amperage, and short circuit current available from utility.” Vista’s handouts call for paper sets.

 

Source: Tenant Improvement – Commercial/Industrial, Updated 12/2018; Industrial/Commercial Building Requirements, Updated 7/2026

​​

El Cajon: Plan Submittal

No signer rule on its permits page; send the correction letter. “Submittals shall be in electronic format via PACO website.”

​

Source: Building Permits, no date shown

submit-electrical-drawings-los-angeles-pe-stamp-service.webp

Electrical Engineer for San Diego Office Tenant Improvements (IB-150)

City of San Diego Information Bulletin 150 (September 2026) covers “Group B interior office tenant improvements less than 20,000 square feet in area with no change of use or occupancy” and requires that “Plans must be stamped and signed by a licensed California Architect or Engineer.”

​

The architect certifies the project: the DS-1500 affidavit is “signed by the licensed California Architect.” The electrical sheets can carry our seal. Two limits matter: the space “Cannot be a first-generation tenant improvement,” and the work can add no “Energy Storage Systems (Batteries) or Uninterrupted Power Supplies (UPS).”

​

“A pre-construction inspection is required to be scheduled before starting work.” If the inspector finds the scope outside the program, “the Professional Certification permit will be canceled.” The contractor schedules and attends inspections. We don’t attend them.

​

For other tenant improvement work, see tenant improvement electrical plans.

​

What to Send for a San Diego Review

Send the set, the correction letter or GC exhibit, the jurisdiction, the deadline, who prepared the drawings, and whether your firm is installing.

​

The last two answers decide whether a contractor may sign: a contractor may design only work it will install itself. See who can sign electrical plans in California.

​

PE Review and Stamp, or a Design Package

We review and stamp contractor-prepared drawings, expedited when needed. When the city or the GC wants an engineer’s design, we prepare the design package. Utility applications stay with the contractor.

​

You receive a permit-ready PDF set: the cover sheet and electrical sheets sealed and signed, with the load calculations and single-line diagram sealed when they are part of the submittal. Plan-check responses on the documents we prepared, with corrections, clarifications, and updated sealed sheets, are included as the proposal defines. Electronic seal is standard; wet-stamped originals by arrangement when a city requires them. A certificate of insurance is available on request.

​

Recent San Diego work: a rush review and seal of a panelboard package for a research lab, followed by the electrical design package, both delivered remotely.

Houses, duplexes, and ADUs are outside this service.

​

For the same service in Los Angeles, see Los Angeles electrical PE stamp. For existing-building work, see facility upgrade electrical plans.

Ready to Send a San Diego Set?

Email the PDF set with the correction letter, the jurisdiction, and your deadline. Tell us who prepared the drawings and whether your firm is installing.

Or email directly: jerry@reddog.engineering

FAQ

1. Does San Diego Require Electrical Plans for a Commercial Tenant Improvement?

Yes. The City of San Diego DSD Plan (required) Electrical Permit page says “Electrical plans and calculations are required for all buildings and structures other than one-and two-family dwellings except when the installation qualifies for a no-plan permit.”

​

2. Can Our C-10 Sign the Electrical Plans in San Diego?

Under the DSD page, only if your firm “is responsible for both the design and installation of the system.” State law draws the same line; see who can sign electrical plans in California. If your firm designs and installs and still wants an engineer on the set, see design-build electrical engineering.

​

3. Do San Diego-Area Cities Accept Electronic Seals and PDF Sets?

State regulation allows an electronic seal and signature (16 CCR 411(e)), and most cities here take PDF sets. Escondido “will only accept plans in an electronic format,” Poway wants “a single .PDF file,” and Oceanside says “Paper plans will no longer be accepted.” Vista’s handouts call for paper sets. We seal electronically, and where a city asks for wet signatures we print, wet-stamp, and deliver originals.

​

4. Can You Review and Stamp Electrical Drawings Our Team Prepared?

Yes. We check every sheet and the calculations behind it, mark up what has to change, and seal the sheets we take responsible charge of. The rule is on who can sign electrical plans in California.

​​

5. How Fast Can You Turn a San Diego Review?

Expedited review is available, and the turnaround is set in the proposal after we review what you send.​

Get a PE Review and Stamp for San Diego County Plans

Email the PDF set, the correction letter, and the utility service report if you have one, or call (626) 428-9005. Scope, turnaround, and fee follow our review of what you send.

  • Review and PE stamp of contractor-prepared electrical drawings

  • Electrical design packages when the city or GC wants an engineer’s design

  • Load calculations, panel schedules, and single-line diagrams

  • Calculations and responses for plan-check corrections

  • Remote delivery; electronic seal standard, wet stamp when a city requires it

Or email directly: jerry@reddog.engineering

About the Engineer

Red Dog Engineering is led by Jerry Poon, PE, California Electrical Engineer License #20878, with 15+ years of MEP engineering and permit-driven electrical design. He has permitted electrical work in most cities in San Diego County and with San Diego County PDS, working remotely alongside the contractors who build it.

​

Jerry reviews every set he seals. He checks the calculations, single-line, and panel schedules against each other and against the field information your shop provides, marks what needs to change, and seals only what he has taken responsibility for. There is no stamp without a review.

​

You deal with the engineer directly, from the first email through plan-check responses, with no account manager in between.

bottom of page